Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE JGS968KHCC
JGS968KHCC is a True Bisque GE Profile slide-in gas range with sealed burners, convection, separate Proof and Warm modes, self-cleaning and a general F function-error display.
Identify the True Bisque gas range
JGS968KHCC is GE Profile's 30-inch slide-in gas range in True Bisque, with a bisque-glass oven door and a lower storage drawer. GE's exact listing describes sealed burners, heavy continuous cast grates and a glass-ceramic cooking surface. The 15,000-BTU Power Boil burner and 5,000-BTU Precise Simmer burner occupy different ends of the heat range; the page also lists 11,000- and 9,100-BTU burners. Turn to the burner diagram before matching a pan to a flame, and keep the continuous grates properly seated after cleaning. QuickSet III glass-touch controls operate the oven, which has an electronic ignition system and halogen cavity light. The linked owner PDF names the JGS968 family. Its power-outage warning is particularly relevant to this gas appliance: the oven and broiler cannot be lit without electricity because gas will not flow until the glow bar becomes hot. Do not infer that the lower storage drawer can cook or warm food. That drawer configuration comes from the exact GE product record rather than optional features on another member of the manual family.
Set convection recipes and rack positions
Convection Bake and Convection Roast are listed for this specific JGS968KHCC. In convection baking the fan distributes hot air around the food, and the guide suggests rack positions D, E and F for three-rack work, with B, D and F if pans do not fit. Install the three heavy-duty racks while the oven is cool, leaving room between pans for air circulation. Auto Recipe Conversion is also listed for this SKU. The manual's example turns an entered conventional 350°F into a displayed 325°F convection setting. It converts temperature only, not cooking time, so check doneness at the recipe's planned time instead of assuming a shorter timer was programmed. This distinction prevents a common double adjustment: if the display already shows the reduced temperature, do not subtract another 25 degrees simply because the fan is running. The oven has an automatic meat thermometer probe, but use the probe procedure and food-temperature target independently of the displayed oven setpoint. Notes about convection and racks help identify a mode-selection issue before treating an uneven batch as a control failure.
Keep proofing, warming and cleaning distinct
The oven's Proof Mode and Warm Mode are both documented for this exact model, and they have different purposes. Put covered yeast dough on rack B or C, touch PROOF and START, and the display reads PrF. The proofing temperature is automatic and cannot be adjusted. The manual explicitly warns that Proof is not hot enough to hold cooked food safely; choose WARM for already cooked food and do not use WARM as a cold-food reheater. A PrF display therefore reports an intended mode, not an error. GE also lists self-cleaning. Before starting, remove racks, broiler equipment, probe, cookware and foil, and wipe heavy spills. The door locks for the cleaning cycle and remains closed until the oven falls below locking temperature. The glass-touch panel may show LOCKED during this process. An owner who presses the wrong key or expects the door to release immediately can misread these ordinary states as a fault. Storage below the cavity, food warming inside the oven and high-heat self-cleaning are three separate functions.
Respond to an F display
On physical PDF page 40, F followed by a number or letter is labeled a function error. The chart does not assign any particular suffix to an igniter, sensor or board. Record the exact characters and the mode in use. The controls page says to press CLEAR/OFF, allow one hour for cooling and put the oven back into operation. If the pattern returns, the troubleshooting page instructs disconnecting all power to the range for at least thirty seconds, reconnecting and calling for service if it repeats again. An F alert has a different meaning from normal PrF proofing. The same troubleshooting section says a flashing LOCKED message can simply mean a self-clean cycle was selected with the door open; close the door for that case. Because the appliance burns gas but relies on electric oven ignition, a power interruption can also stop heating without implying the F component fault. These steps separate a display observation from an unsupported parts diagnosis. Use the official PDF for the full safety instructions and service path.
Verified model details
Its 15,000-BTU Power Boil burner and 5,000-BTU Precise Simmer burner serve different heat tasks.
Source for this detail · Source page: 1PrF is the normal proofing display; Proof must not be used to hold cooked food hot.
Source for this detail · Source page: 40F plus a character requires CLEAR/OFF, cooling and a power reset if the error repeats.
Source for this detail · Source page: 23
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE Profile™ 30" Slide-In Gas Range - JGS968KHCC - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.