MODEL PROFILE
Signal or code
Error codes and display signals
The official manual linked for this model documents these messages. Some indicators apply only to variants that display them; each entry is labeled as a code, indicator, or status.
No matching signal for this model.
Model and error-code facts may be shown in the language of the original source.
Official PDF manual
Jump to manual pages
Open the official PDF at pages that document signals for this model.
MODEL OVERVIEW
About this model: GE GDWT160RSS
The GE GDWT160RSS's START/RESET drain status, top-control panel, sensor cycles, loading and stainless care explained from its official linked manual.
Identify the stainless top-control model
The GE GDWT160RSS is a stainless-steel, built-in dishwasher whose exact product specification identifies a stainless tub and inner door, sixteen place settings and fully integrated top controls with six touchpads. That combination is the useful identity check before following the broad owner booklet. Its cover says only 'stainless steel tub dishwashers' and does not spell out this sales suffix, while the exact GE product page supplies the direct owner-PDF link. The rendered page-four drawing includes a top-control configuration with START/RESET and progress lamps, consistent with the specified controls. The same booklet also draws front-control and optional SmartDispense versions; these pictures should not be read as promises that GDWT160RSS has every depicted feature. The product lists a QuietPower 52 package at 52 dBA and a one-piece silverware basket. Keep the model label on the tub wall in view when comparing the panel.
What flashing START/RESET actually reports
Unlike a numbered component code, flashing START/RESET is a process signal. Page sixteen places it under 'Error Messages' but explains two ordinary paths: a press of START/RESET during a running wash cancels the cycle, or power returned after an interruption. In both cases the machine drains, with the troubleshooting table describing about ninety seconds before the light stops. Page six gives the top-control reset instruction as roughly two minutes and says to close the door while water pumps out. Page seven says a power-interrupted cycle can restart automatically after drainage, so repeated button presses may confuse the sequence. The exact product specifies last-cycle memory and a Control Lock; a steady CLEAN or SANITIZED lamp carries a different meaning. A door left open during operation can produce a beep every thirty seconds. Observe which lamp flashes, whether the door was opened, and whether electricity failed before treating this as an appliance defect.
Cycles, sensing and the end of drying
The GDWT160RSS product record names Normal Wash, Rinse Only, Light Wash and Pots & Pans among its wash choices, with a Clean Sensor to adjust for conditions. The manual's normal-program time is a range rather than a fixed promise, because soil level, incoming water and household pressure affect it. The exact model offers two-, four- and eight-hour delayed starts; waiting during a selected delay is not a failure to run. Its fan-assisted convection drying also changes what an owner hears after the wash phase. The common manual says a top-control fan may keep operating after the CLEAN light, and completion can bring two beeps. CLEAN therefore should not be confused with flashing START/RESET. Control Lock prevents selections; the booklet directs a three-second hold of HEATED DRY to release it. These documented control states deserve checking before assuming a damaged electronic board.
Link poor washing to water and loading
The product page specifies a Piranha hard-food disposer, a self-cleaning triple filtration system with an extra-fine stage, and a one-piece cutlery basket with divided covers. Those physical details make a gritty load a different investigation from a blinking reset lamp. Page twelve warns that utensils projecting below a rack can obstruct the middle spray arm, lowering performance even if the controller proceeds normally. GE specifies incoming water between 120 and 150 degrees Fahrenheit; cooler supply can weaken washing and drying. The manual detergent cup is filled according to water hardness, not simply to the rim for every home, while the exact unit's rinse-aid dispenser can be adjusted separately. Normal pre-rinsing is unnecessary, but scrape hard bones, seeds and excess grease. Check rack clearance, water supply and detergent amount in a deliberate order, then report the observations alongside any true display signal.
Care for the SS finish without inventing codes
The final two letters SS identify the stainless exterior care instructions in this PDF, matching the product's stainless finish and interior. GE recommends a soft cloth and appropriate stainless cleaner for the outside panel, without bleach or chlorine products; the top electronic control should be wiped lightly damp and dried. For spots, examine the rinse-aid setting, water hardness and temperature. Page seventeen separates cloudy glass caused by permanent etching from ordinary removable film: too much detergent with soft water can etch, and water hotter than 150 degrees Fahrenheit is another possible cause. A clogged air gap or a pot handle blocking the spray path belongs to water-flow troubleshooting, not the START/RESET status table. The linked owner's guide gives no numeric fault list for GDWT160RSS. Its actionable published signal is the timed drain and possible restart following interruption; keep that interpretation separate from guesses about failed parts.
Verified model details
Exact stainless tub and six-pad top panel distinguish this model from other configurations in its shared manual.
Source for this detailSTART/RESET flashing means automatic drainage after cancellation or restored power; no numeric component code is claimed.
Source for this detail · Source page: 16The exact SKU combines Clean Sensor, fan-assisted drying, a triple filter and 2/4/8-hour delay choices.
Source for this detail · Source page: 7
This description summarizes the linked source documents; check each cited source for your exact model and region.
Manufacturer source
Open official source
GE® Built-In Dishwasher with Hidden Controls - GDWT160RSS - GE Appliances
Open official sourceIf there is a safety risk, stop using the appliance and follow the manufacturer’s instructions.